root/include/uapi/linux/usb/ch11.h

INCLUDED FROM

/*
 * This file holds Hub protocol constants and data structures that are
 * defined in chapter 11 (Hub Specification) of the USB 2.0 specification.
 *
 * It is used/shared between the USB core, the HCDs and couple of other USB
 * drivers.
 */

#ifndef __LINUX_CH11_H
#define __LINUX_CH11_H

#include <linux/types.h>        /* __u8 etc */

/* This is arbitrary.
 * From USB 2.0 spec Table 11-13, offset 7, a hub can
 * have up to 255 ports. The most yet reported is 10.
 *
 * Current Wireless USB host hardware (Intel i1480 for example) allows
 * up to 22 devices to connect. Upcoming hardware might raise that
 * limit. Because the arrays need to add a bit for hub status data, we
 * use 31, so plus one evens out to four bytes.
 */
#define USB_MAXCHILDREN         31

/*
 * Hub request types
 */

#define USB_RT_HUB      (USB_TYPE_CLASS | USB_RECIP_DEVICE)
#define USB_RT_PORT     (USB_TYPE_CLASS | USB_RECIP_OTHER)

/*
 * Hub class requests
 * See USB 2.0 spec Table 11-16
 */
#define HUB_CLEAR_TT_BUFFER     8
#define HUB_RESET_TT            9
#define HUB_GET_TT_STATE        10
#define HUB_STOP_TT             11

/*
 * Hub class additional requests defined by USB 3.0 spec
 * See USB 3.0 spec Table 10-6
 */
#define HUB_SET_DEPTH           12
#define HUB_GET_PORT_ERR_COUNT  13

/*
 * Hub Class feature numbers
 * See USB 2.0 spec Table 11-17
 */
#define C_HUB_LOCAL_POWER       0
#define C_HUB_OVER_CURRENT      1

/*
 * Port feature numbers
 * See USB 2.0 spec Table 11-17
 */
#define USB_PORT_FEAT_CONNECTION        0
#define USB_PORT_FEAT_ENABLE            1
#define USB_PORT_FEAT_SUSPEND           2       /* L2 suspend */
#define USB_PORT_FEAT_OVER_CURRENT      3
#define USB_PORT_FEAT_RESET             4
#define USB_PORT_FEAT_L1                5       /* L1 suspend */
#define USB_PORT_FEAT_POWER             8
#define USB_PORT_FEAT_LOWSPEED          9       /* Should never be used */
#define USB_PORT_FEAT_C_CONNECTION      16
#define USB_PORT_FEAT_C_ENABLE          17
#define USB_PORT_FEAT_C_SUSPEND         18
#define USB_PORT_FEAT_C_OVER_CURRENT    19
#define USB_PORT_FEAT_C_RESET           20
#define USB_PORT_FEAT_TEST              21
#define USB_PORT_FEAT_INDICATOR         22
#define USB_PORT_FEAT_C_PORT_L1         23

/*
 * Port feature selectors added by USB 3.0 spec.
 * See USB 3.0 spec Table 10-7
 */
#define USB_PORT_FEAT_LINK_STATE                5
#define USB_PORT_FEAT_U1_TIMEOUT                23
#define USB_PORT_FEAT_U2_TIMEOUT                24
#define USB_PORT_FEAT_C_PORT_LINK_STATE         25
#define USB_PORT_FEAT_C_PORT_CONFIG_ERROR       26
#define USB_PORT_FEAT_REMOTE_WAKE_MASK          27
#define USB_PORT_FEAT_BH_PORT_RESET             28
#define USB_PORT_FEAT_C_BH_PORT_RESET           29
#define USB_PORT_FEAT_FORCE_LINKPM_ACCEPT       30

#define USB_PORT_LPM_TIMEOUT(p)                 (((p) & 0xff) << 8)

/* USB 3.0 hub remote wake mask bits, see table 10-14 */
#define USB_PORT_FEAT_REMOTE_WAKE_CONNECT       (1 << 8)
#define USB_PORT_FEAT_REMOTE_WAKE_DISCONNECT    (1 << 9)
#define USB_PORT_FEAT_REMOTE_WAKE_OVER_CURRENT  (1 << 10)

/*
 * Hub Status and Hub Change results
 * See USB 2.0 spec Table 11-19 and Table 11-20
 */
struct usb_port_status {
        __le16 wPortStatus;
        __le16 wPortChange;
} __attribute__ ((packed));

/*
 * wPortStatus bit field
 * See USB 2.0 spec Table 11-21
 */
#define USB_PORT_STAT_CONNECTION        0x0001
#define USB_PORT_STAT_ENABLE            0x0002
#define USB_PORT_STAT_SUSPEND           0x0004
#define USB_PORT_STAT_OVERCURRENT       0x0008
#define USB_PORT_STAT_RESET             0x0010
#define USB_PORT_STAT_L1                0x0020
/* bits 6 to 7 are reserved */
#define USB_PORT_STAT_POWER             0x0100
#define USB_PORT_STAT_LOW_SPEED         0x0200
#define USB_PORT_STAT_HIGH_SPEED        0x0400
#define USB_PORT_STAT_TEST              0x0800
#define USB_PORT_STAT_INDICATOR         0x1000
/* bits 13 to 15 are reserved */

/*
 * Additions to wPortStatus bit field from USB 3.0
 * See USB 3.0 spec Table 10-10
 */
#define USB_PORT_STAT_LINK_STATE        0x01e0
#define USB_SS_PORT_STAT_POWER          0x0200
#define USB_SS_PORT_STAT_SPEED          0x1c00
#define USB_PORT_STAT_SPEED_5GBPS       0x0000
/* Valid only if port is enabled */
/* Bits that are the same from USB 2.0 */
#define USB_SS_PORT_STAT_MASK (USB_PORT_STAT_CONNECTION |           \
                                USB_PORT_STAT_ENABLE |      \
                                USB_PORT_STAT_OVERCURRENT | \
                                USB_PORT_STAT_RESET)

/*
 * Definitions for PORT_LINK_STATE values
 * (bits 5-8) in wPortStatus
 */
#define USB_SS_PORT_LS_U0               0x0000
#define USB_SS_PORT_LS_U1               0x0020
#define USB_SS_PORT_LS_U2               0x0040
#define USB_SS_PORT_LS_U3               0x0060
#define USB_SS_PORT_LS_SS_DISABLED      0x0080
#define USB_SS_PORT_LS_RX_DETECT        0x00a0
#define USB_SS_PORT_LS_SS_INACTIVE      0x00c0
#define USB_SS_PORT_LS_POLLING          0x00e0
#define USB_SS_PORT_LS_RECOVERY         0x0100
#define USB_SS_PORT_LS_HOT_RESET        0x0120
#define USB_SS_PORT_LS_COMP_MOD         0x0140
#define USB_SS_PORT_LS_LOOPBACK         0x0160

/*
 * wPortChange bit field
 * See USB 2.0 spec Table 11-22 and USB 2.0 LPM ECN Table-4.10
 * Bits 0 to 5 shown, bits 6 to 15 are reserved
 */
#define USB_PORT_STAT_C_CONNECTION      0x0001
#define USB_PORT_STAT_C_ENABLE          0x0002
#define USB_PORT_STAT_C_SUSPEND         0x0004
#define USB_PORT_STAT_C_OVERCURRENT     0x0008
#define USB_PORT_STAT_C_RESET           0x0010
#define USB_PORT_STAT_C_L1              0x0020
/*
 * USB 3.0 wPortChange bit fields
 * See USB 3.0 spec Table 10-11
 */
#define USB_PORT_STAT_C_BH_RESET        0x0020
#define USB_PORT_STAT_C_LINK_STATE      0x0040
#define USB_PORT_STAT_C_CONFIG_ERROR    0x0080

/*
 * wHubCharacteristics (masks)
 * See USB 2.0 spec Table 11-13, offset 3
 */
#define HUB_CHAR_LPSM           0x0003 /* Logical Power Switching Mode mask */
#define HUB_CHAR_COMMON_LPSM    0x0000 /* All ports power control at once */
#define HUB_CHAR_INDV_PORT_LPSM 0x0001 /* per-port power control */
#define HUB_CHAR_NO_LPSM        0x0002 /* no power switching */

#define HUB_CHAR_COMPOUND       0x0004 /* hub is part of a compound device */

#define HUB_CHAR_OCPM           0x0018 /* Over-Current Protection Mode mask */
#define HUB_CHAR_COMMON_OCPM    0x0000 /* All ports Over-Current reporting */
#define HUB_CHAR_INDV_PORT_OCPM 0x0008 /* per-port Over-current reporting */
#define HUB_CHAR_NO_OCPM        0x0010 /* No Over-current Protection support */

#define HUB_CHAR_TTTT           0x0060 /* TT Think Time mask */
#define HUB_CHAR_PORTIND        0x0080 /* per-port indicators (LEDs) */

struct usb_hub_status {
        __le16 wHubStatus;
        __le16 wHubChange;
} __attribute__ ((packed));

/*
 * Hub Status & Hub Change bit masks
 * See USB 2.0 spec Table 11-19 and Table 11-20
 * Bits 0 and 1 for wHubStatus and wHubChange
 * Bits 2 to 15 are reserved for both
 */
#define HUB_STATUS_LOCAL_POWER  0x0001
#define HUB_STATUS_OVERCURRENT  0x0002
#define HUB_CHANGE_LOCAL_POWER  0x0001
#define HUB_CHANGE_OVERCURRENT  0x0002


/*
 * Hub descriptor
 * See USB 2.0 spec Table 11-13
 */

#define USB_DT_HUB                      (USB_TYPE_CLASS | 0x09)
#define USB_DT_SS_HUB                   (USB_TYPE_CLASS | 0x0a)
#define USB_DT_HUB_NONVAR_SIZE          7
#define USB_DT_SS_HUB_SIZE              12

/*
 * Hub Device descriptor
 * USB Hub class device protocols
 */

#define USB_HUB_PR_FS           0 /* Full speed hub */
#define USB_HUB_PR_HS_NO_TT     0 /* Hi-speed hub without TT */
#define USB_HUB_PR_HS_SINGLE_TT 1 /* Hi-speed hub with single TT */
#define USB_HUB_PR_HS_MULTI_TT  2 /* Hi-speed hub with multiple TT */
#define USB_HUB_PR_SS           3 /* Super speed hub */

struct usb_hub_descriptor {
        __u8  bDescLength;
        __u8  bDescriptorType;
        __u8  bNbrPorts;
        __le16 wHubCharacteristics;
        __u8  bPwrOn2PwrGood;
        __u8  bHubContrCurrent;

        /* 2.0 and 3.0 hubs differ here */
        union {
                struct {
                        /* add 1 bit for hub status change; round to bytes */
                        __u8  DeviceRemovable[(USB_MAXCHILDREN + 1 + 7) / 8];
                        __u8  PortPwrCtrlMask[(USB_MAXCHILDREN + 1 + 7) / 8];
                }  __attribute__ ((packed)) hs;

                struct {
                        __u8 bHubHdrDecLat;
                        __le16 wHubDelay;
                        __le16 DeviceRemovable;
                }  __attribute__ ((packed)) ss;
        } u;
} __attribute__ ((packed));

/* port indicator status selectors, tables 11-7 and 11-25 */
#define HUB_LED_AUTO    0
#define HUB_LED_AMBER   1
#define HUB_LED_GREEN   2
#define HUB_LED_OFF     3

enum hub_led_mode {
        INDICATOR_AUTO = 0,
        INDICATOR_CYCLE,
        /* software blinks for attention:  software, hardware, reserved */
        INDICATOR_GREEN_BLINK, INDICATOR_GREEN_BLINK_OFF,
        INDICATOR_AMBER_BLINK, INDICATOR_AMBER_BLINK_OFF,
        INDICATOR_ALT_BLINK, INDICATOR_ALT_BLINK_OFF
} __attribute__ ((packed));

/* Transaction Translator Think Times, in bits */
#define HUB_TTTT_8_BITS         0x00
#define HUB_TTTT_16_BITS        0x20
#define HUB_TTTT_24_BITS        0x40
#define HUB_TTTT_32_BITS        0x60

#endif /* __LINUX_CH11_H */